Dead by Daylight
An asymmetrical horror game locked at 60 FPS. It is generally GPU-limited at high settings but runs on most mid-range hardware.
This game has a built-in FPS cap of 60 FPS
Actual FPS may vary based on RAM speed, background processes, and other system factors
Performance Report
At 1080p, performance runs at around 47 FPS. At 1440p, frame rates range from 45 to 47 FPS. At 4K, frame rates range from 35 to 45 FPS.
The GeForce RTX 4090 is 692% above the recommended GPU (GeForce GTX 760) for Dead by Daylight. The Pentium G3260T is 72% below minimum CPU requirement.
The Pentium G3260T sets the FPS ceiling at all 1080p settings, all 1440p settings, all 4k settings, while the GeForce RTX 4090 still has headroom.
This chart answers a simple question: which upgrade is more likely to increase FPS first? In this case, the answer is clearly the CPU.
The largest gap appears at 1080p Low, where the Pentium G3260T reaches about 47 FPS, while the GeForce RTX 4090 still has headroom up to roughly 274 FPS.
That means the Pentium G3260T is hitting its performance ceiling first, leaving a 83% gap versus the GeForce RTX 4090's available headroom in the most unbalanced scenario. Across all tested settings, this pairing is CPU-limited in 12 out of 12 cases, with 0 GPU-limited and 0 balanced results.
Overall, this is a clearly CPU-bound combination in this game.
The Pentium G3260T is consistently the limiting part in this game, so upgrading the CPU is more likely to deliver a larger FPS gain than upgrading the GPU.
This chart shows which upgrade is more likely to unlock more FPS in each tested setting. The lower line represents the part that reaches its limit first. When the CPU and GPU lines stay close together, the system is more balanced. When the gap widens, one component is more clearly holding the other back. Hover any setting to inspect it.
The lower line is the current limiter. The closer the two lines are, the more balanced the CPU and GPU are for this game.
Each line represents an estimated FPS ceiling for one component, rather than live usage alone.
To estimate the CPU ceiling, we pair the Pentium G3260T with GeForce RTX 5090, our current GPU anchor. To estimate the GPU ceiling, we pair the GeForce RTX 4090 with Ryzen 9 9950X3D, our current CPU anchor.
The lower line indicates the current limiter, since that component reaches its FPS ceiling first. In most scenarios, that is also the part most likely to deliver the bigger performance uplift if upgraded first.
The percentage shown represents the gap between the two ceilings. In practical terms, it shows how much of the stronger component's potential is left unused because the weaker one becomes the bottleneck first.
See how your processor and graphics card compare against the game official minimum and recommended system specs. The placement of your hardware is calculated using relative synthetic performance scores to help you gauge overall playability.
Your hardware is below minimum requirements. CPU is the limiting factor (72% below minimum). Expect performance issues. Low settings recommended.
-65%vsrecommended
+692%vsrecommended
-72%vsminimum
+1575%vsminimum
The Pentium G3260T and GeForce RTX 4090 will struggle to run Dead by Daylight at smooth framerates. At 1080p Ultra, you can expect around 47 FPS which is classified as "playable". Consider lowering settings or upgrading your hardware.
Price data is not currently available for this combination. In general, look for setups where the CPU and GPU are balanced - this ensures you're not overspending on one component that the other can't keep up with.
For Dead by Daylight, upgrading the CPU would usually improve performance first. In the Performance Limiter Analysis, the Pentium G3260T is the side that most often caps the frame rate, while the GeForce RTX 4090 still has additional headroom in the tested presets. The main bottleneck appears on the CPU side. The largest gap shows up at 1080p Low, where the CPU reaches about 47 FPS while the GPU still has headroom up to roughly 274 FPS. Across all tested settings, the distribution is 0/12 GPU-limited, 12/12 CPU-limited, and 0/12 balanced.
Dead by Daylight does not currently support Frame Generation technologies like DLSS 3 or FSR 3. Your performance is based entirely on native rendering. If the game adds support in a future update, newer GPUs will benefit the most.
Dead by Daylight requires at minimum a Core i3-4170 (CPU) and GeForce GTX 460 (GPU) with 8 GB RAM and 50 GB storage. For the recommended experience, you need a Core i3-4170 and GeForce GTX 760 with 8 GB RAM. Your hardware falls below the minimum requirements for this game, which may result in poor performance.
These Dead by Daylight FPS results are not arbitrary numbers. They come from calculations informed by thousands of real gaming benchmarks, and the typical accuracy range is around 10% to 15%. That makes them far more useful than generic FPS calculators that simply invent values without a benchmark foundation. Actual in-game performance can still vary with drivers, updates, RAM configuration, cooling, and the exact scene being rendered.
Performance estimates are based on synthetic benchmarks and hardware capabilities.
Results may vary based on drivers, OS, and background processes.
